Standby generator installed — certified for Generac
Generac standby generators with an automatic transfer switch, sized for what you want running when the power’s out across southwest Washington — or a manual transfer switch and inlet for the portable generator you already own. Permitted, inspected, and warrantied for two years.
Free estimates on installs · $125 to diagnose, credited to the repair
Licensed, bonded, and insured · WA #TRUWOEL745MO
- Licensed · bonded · insured
- Two-year labor warranty
- Upfront pricing
- Evenings and weekends
What’s included
- Load review — what you want on during an outage and what size unit carries it
- Generator placement checked against the manufacturer’s clearances and code
- Automatic transfer switch installed and tested (or a manual transfer switch and inlet for a portable)
- Coordination with your gas or propane contractor for the fuel line
- Startup, a test outage, and a walkthrough of how it works
- Permit pulled by Truworx — you don’t deal with L&I
- L&I inspection scheduled and passed, with the paperwork left with you
- Cleanup — packaging and old parts hauled off, floors vacuumed
- Two-year warranty on labor
What it costs
The big decision is whole-house or essentials. A whole-house unit carries everything, including the heat pump and range, and costs more. An essentials setup runs the furnace or a heat pump, the fridge and freezer, the well pump, some lights and outlets, and the garage door — and that’s what most homes actually need for a two-day outage.
What else moves the number: the generator size in kilowatts, how far the unit sits from the panel and the gas meter, whether it’s natural gas or propane, and the transfer switch type. The gas or propane line is done by a licensed gas contractor and quoted separately by them. Permit fees are passed through at cost.
The lower-cost option is a manual transfer switch and an outdoor inlet for a portable generator you own or buy. You roll it out, plug it in, flip the switch, and run the essentials. Free estimates on installs, either way.
How it goes
- You call or text. I come out, look at your panel, meter, and where the unit would sit, and give you a number.
- I order the generator and transfer switch and pull the permit. You line up a gas contractor for the fuel line, or I can point you to one.
- Install day: pad, wiring, and transfer switch. Once the gas is connected, I start it up and walk you through it.
- L&I inspects. I set the weekly self-test, and you’re covered for the next outage.
Good to know
Whole-house or just the essentials?
Essentials, for most homes. A unit that runs the furnace or heat pump, fridge and freezer, well pump, a few lighting and outlet circuits, and the garage door covers a multi-day outage comfortably, and it costs a lot less than a whole-house unit. Whole-house makes sense if you have medical equipment, a large home with electric heat, or you just don’t want to think about it. I’ll walk your panel with you and we’ll pick.
What size generator do I need?
It comes from the load review — adding up what you want running, with attention to motors like the well pump and heat pump that pull a surge when they start. Air-cooled Generac units for homes typically range from about 10 to 26 kilowatts. I’ll size it to what you actually need and show you the math, so you’re not paying for capacity you’ll never use.
Do you handle the gas line?
The electrical, yes — the gas or propane line, no. That has to be done by a licensed gas or plumbing contractor under a separate permit. I coordinate the timing so the gas contractor comes when the unit is set, and I don’t fire it up until their side is inspected. If you don’t have someone, I can recommend a couple.
How long from estimate to running?
Plan on three to six weeks. Most of that is the generator’s lead time and lining up the gas contractor and the permits. The electrical install itself is one to two days. If your utility has been having outages and you want it done before winter, call in late summer.
What about a manual transfer switch for a portable generator?
It’s a good option and a lot less money. I install a manual transfer switch at your panel, wired to the circuits you choose, and an inlet on the outside of the house. When the power goes out, you roll the portable out, plug it into the inlet, start it, and flip the switch. No extension cords through windows, and it’s safe for the line workers. It still needs a permit and an inspection.
Service area
Serving Brush Prairie, Vancouver, Battle Ground, Ridgefield, La Center, Kalama, Kelso, and Longview — Clark and Cowlitz counties, southwest Washington.
Standby generator installation in southwest Washington — tell me what you want to keep running.
Free estimates on installs · $125 to diagnose, credited to the repair
Or text (509) 565-0103 — I’ll answer between jobs.
Licensed, bonded, and insured · WA #TRUWOEL745MO
