Hot tub, shop subpanel, and RV plug wiring — permitted and inspected
50-amp hot tub circuits with the disconnect, subpanels for garages and outbuildings, and 30- or 50-amp RV outlets, anywhere in Clark County and southwest Washington. Trenching coordinated, permit pulled, inspection passed, and a two-year warranty on the labor.
Free estimates on installs · $125 to diagnose, credited to the repair
Licensed, bonded, and insured · WA #TRUWOEL745MO
- Licensed · bonded · insured
- Two-year labor warranty
- Upfront pricing
- Evenings and weekends
What’s included
- Load calculation, so the new circuit or subpanel fits what your panel can carry
- GFCI protection and the disconnect the code requires for a hot tub, placed where the inspector wants it
- Subpanels sized to what you’ll actually run — welder, compressor, heat, lights
- Trench depth and conduit spec’d for you or your excavator, and the feeder pulled once it’s open
- Permit pulled by Truworx — you don’t deal with L&I
- L&I inspection scheduled and passed, with the paperwork left with you
- Cleanup — packaging and old parts hauled off, floors vacuumed
- Two-year warranty on labor
What it costs
For all three of these, distance is the biggest factor: how far the hot tub, shop, or RV pad is from the panel, and whether the run is through the house, along the outside, or underground in a trench. Underground runs need conduit and a trench at code depth, and a long feeder to a shop means heavier wire.
The second factor is your panel. A 50-amp hot tub circuit or a 60- to 100-amp shop feeder takes real capacity, and if the panel doesn’t have it, a service upgrade is part of the conversation. Permit fees are passed through at cost. You can dig the trench yourself, hire an excavator, or have Truworx arrange it.
Free estimates on installs. A photo of the panel and a photo or sketch of where things are going is enough to start.
How it goes
- You call or text with what you’re powering and where. I’ll ask for a photo of the panel and give you a number, or come out to walk the route.
- I pull the permit and spec the trench. You dig it, your excavator does, or I line one up — your call.
- Install day: I text when I’m on my way, pull the feeder, set the disconnect, subpanel, or RV outlet, and test it.
- L&I inspects (the trench is inspected before it’s backfilled) and you get the passed permit.
Good to know
What does a hot tub need electrically?
Most hot tubs need a dedicated 50-amp, 240-volt GFCI-protected circuit, a disconnect switch within sight of the tub but at least five feet away, and bonding of the tub’s metal parts. Some smaller tubs run on a 40- or 60-amp circuit, and a few plug into a regular outlet — check the manual or send me the model. The run from the panel to the tub is what sets the price.
Can you run power to my shop?
Yes. A shop gets a subpanel fed by a buried feeder from the main house, sized to what you’ll run — a 60-amp subpanel covers lights, outlets, and a compressor; a welder or a heater pushes you to 100 amps. I spec the trench and conduit, pull the feeder once it’s open, set the subpanel, and wire the shop from there if you want.
30 amp or 50 amp RV plug?
Match the RV. Most travel trailers and smaller motorhomes use a 30-amp plug (one air conditioner); larger fifth-wheels and motorhomes with two air conditioners use 50-amp. If you’re not sure which you’ll own next, a 50-amp outlet with a 30-amp adapter covers both. Either one needs its own breaker and a weatherproof pedestal or box near where the RV parks.
Who digs the trench?
Your choice. A lot of homeowners dig it themselves or have a friend with a mini excavator do it; I give you the exact route, depth (usually 18 to 24 inches depending on the conduit type), and width, and I lay the conduit. Or I can arrange an excavator and include it in the number. Either way, call 811 before digging, and the trench stays open until the inspector has seen the conduit.
Do these need a permit?
Yes, all three. A hot tub circuit, a subpanel, and an RV outlet are each new circuits that require an L&I electrical permit and an inspection in Washington, and underground runs get inspected before backfill. I pull the permit and meet the inspector. The passed permit matters when you sell the house, and for the hot tub it matters to your insurance company.
Service area
Serving Brush Prairie, Vancouver, Battle Ground, Ridgefield, La Center, Kalama, Kelso, and Longview — Clark and Cowlitz counties, southwest Washington.
Hot tub, shop, and RV circuits in Clark County — tell me what you’re powering and I’ll give you a number.
Free estimates on installs · $125 to diagnose, credited to the repair
Or text (509) 565-0103 — I’ll answer between jobs.
Licensed, bonded, and insured · WA #TRUWOEL745MO
